PA-CF Low Warp

 79,94 TTC

Le PA-CF Low Warp and un polyamide qui permet une impression sur des plateau non chauffé avec quasiment zéro warping. Le PA-CF est un filament ultra résistant aux étirements et aux impacts et résiste également aux températures jusqu’à 120°c en gardant des bonnes propriétés mécaniques.

Le PA-CF contient des particules de carbone et doit être imprimé avec une buse résistante (Acier inox ou ruby).

1.751.751.752.852.852.85
Effacer
Stock
UGS : IdeaTo3d_7866 Catégorie :

Description

Le PA-CF Low Warp and un polyamide qui permet une impression sur des plateau non chauffé avec quasiment zéro warping. Le PA-CF est un filament ultra résistant aux étirements et aux impacts et résiste également aux températures jusqu’à 120°c en gardant des bonnes propriétés mécaniques.

Le PA-CF contient des particules de carbone et doit être imprimé avec une buse résistante (Acier inox ou ruby).

CARBON FIBER IS ABRASIVE

A special point of attention is the abrasive nature of the carbon fibers. In general these fibers will accelerate the nozzle-wear of brass nozzles, much faster than unfilled filaments. ColorFabb recommends to using wear resistant nozzles, such as E3D hardened steel nozzle, 3DSolex Steel or Everlast nozzles or Olsson Ruby nozzle.

 

Specifications

The PA-CF Low Warp is a one of a kind polyamide formulation with the ability to print nearly warp free on non heated buildplatforms. Low infill prints come out perfectly flat on cold bed for higher infill prints 40/50C temperature is enough to obtain flat prints.

PA-CF low warp is infused with carbon fiber for increased stiffness. Users are recommended to use wear resistant nozzles, such as E3D Hardened steel nozzle or Olsson Ruby.

PA-CF Low Warp excels in tensile and impact strength and allows continues use at 120°C while retaining sufficient mechanical properties.

The formulation has been modified to reduce uptake of moisture and it also takes about 4 times longer to reach the saturation point compared to unmodified PA6. This makes PA-CF Low Warp less affected by moisture then most other nylon filaments available in the market.

CARBON FIBER IS ABRASIVE

A special point of attention is the abrasive nature of the carbon fibers. In general these fibers will accelerate the nozzle-wear of brass nozzles, much faster than unfilled filaments. ColorFabb recommends to using wear resistant nozzles, such as E3D hardened steel nozzle or Olsson Ruby nozzle.

Due to high stiffness of 2.85mm filament we recommend users to use spoolmounts which have some friction between spool and holder, to prevent unspooling of filament.

Adviced 3d printing temperature:
260C-280C

Adviced 3d print speed:
30 – 40 mm/s

Advised Heated bed (if you have one, not strictly necessary):
ambient – 50C

For heated glass plate buildsurface we can recommend using 3DLac for extra adhesion.

Advised layerheight
For this material we recommend a minimum of 0.2mm layerheight. Due to the length of the fibers layers lower then 0.15mm can cause issues such as clogging or partial clogging of the nozzle.

Cooling fan
50% fan cooling is a good starting point, this gives best performance on overhangs and small details. For best mechanical performance try printing with the least amount of cooling needed, for optimal layer adhesion.

Informations complémentaires

Poids 0.75 kg
Diamètre

1.75, 2,85, 2.85

Customers' review

5 stars 0 0 %
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

Reviews

There are no reviews yet.

Be the first to review “PA-CF Low Warp”